The new, 5,000-square-meter facility includes demonstration, integration, training and office space.
Designed to accommodate four workers, including their service equipment, and can raise its infinitely adjustable platform to a maximum height of eight meters.
Morgan Crucible has combined its two divisions Morgan Ceramics and Morgan Engineered Materials to create a unified business under the new name Morgan Advanced Materials.
Fully automated test system for all driveline and electric motor testing
Trust Automation designed and developed critical motion control elements to the radar platform.
AlphaLab Gear is a new accelerator located in Pittsburgh that converges manufacturing, technology and ingenuity for hardware & robotics startups
MMS 22-PI1 magnetic switch from SCHUNK, uses two programmable switching points, making it an all-purpose sensor.
First of two new SXUV multi-element photodiodes to be introduced
LIT Dinner to Honor Top Technologists and Policymakers Instrumental in Advancing Technology Innovation
According to AllThingsD Apple is in the process of buying PrimeSense. PrimeSense is the company that developed and licensed the hardware and chip design used in the original Kinect. This could have an effect on several low cost depth cameras including the ASUS Xtion which uses PrimeSense hardware or the $200 developer camera sold directly from PrimeSense . Their online store is still open but who know for how long.
IEEE Spectrum: As cool as quadrotors are, in most cases they're simply not as good as helicopters. Because of the way they're designed (with four small rotors instead of one big one), they're less powerful, less efficient, and less maneuverable. The power and efficiency issues come from the fact that one big rotor generates more lift per aircraft footprint than four small rotors, and as for maneuverability, a helicopter that can alter rotor pitch instantly will always outmaneuver a quadrotor that can only control blade speed. Seriously, try doing this with a quadrotor. So, the thing that quadrotors have going for them is that they're simple. Helicopters have complex main rotor heads, with shafts and bearings and linkages all over the place, while quadrotors just have four motors and that's it. The University of Queensland researchers came up with a "Y4" configuration that aims to take all the good bits of helicopters and make them as simple as quadrotors. I'm just going to start calling this new design a triquad. Keep in mind that this is still a quadrotor: it just had things shifted around a little bit. Almost all of the triquad's lift comes from its big main fixed-pitch rotor, located at the center of the "Y" (pictured below). The three little fixed-pitch rotors in the "Y" configuration are angled (at a fixed 45 degrees) to provide counter-torque (which they do slightly more efficiently than a helicopter tail rotor) along with pitch and roll control. Here's how the control works... cont'd at IEEE Spectrum Follow up discussions: DIY Drones post and discussion. Hackernews post.
Harvest Automation robots are designed to work around the clock, they never need a break, and can handle the most tedious and repetitive work on a Nursery or Greenhouse operation with consistent accuracy and on-time performance.
TORC's unmanned ground vehicle (UGV) conversion kits, which maintain the ability for optionally manned operation, offer the proven capabilities and modularity necessary for AFRL to scale from one prototype to production quantity.
CoaXpress and MatLab integration offer options where previously none existed. The ability to have a controllable high speed camera at distances greater than 7m wasn't a possibility before, without the use of extenders and other potential hardware failures.
With over 35,000 attendees and 1500 exhibitors this provides an excellent platform for the market launch of the Delta E rotator.
Records 3676 to 3690 of 6713
Industrial Robotics - Featured Product
Program and simulate ALL your robots with OCTOPUZ offline software. OCTOPUZ specializes in path sensitive robotic applications such as welding, fabrication, edge following (waterjet, deburring, laser cutting), material removal (2D & 3D machining), and pick & place. Easy to learn, it directly supports paths from your favorite CAM system, has a library of over 15 different types of robot brands, can cut path generation by over 50% and is fully customizable to your unique needs. Program and simulate multiple robots simultaneously in any configuration! Responsive technical assistance from OCTOPUZ before, during and after sale via training, support and cell development make OCTOPUZ the software of choice.