Register Your Company Here

Manufacturing
Marketing Partner


Novotechnik

Novotechnik

Novotechnik develops and manufactures a wide variety of rotary angle sensors and linear position transducers, potentiometers, components and other related products for motion control. All of our products are produced to the same standards of the highest quality and true reliability.


Mailing Address:
155 Northboro Roa
Southborough, MA 01772
United States of America

Tel: 800-667-7492

Fax: 508-485-2430

Email: info@novotechnik.com

Website: http://www.novotechnik.com

Company Category: Factory Automation

Geographic Region: USA - North East

Company Sector: Manufacturing

Keywords: position sensors, linear sensors, position transducers

Partner Status: Marketing Partner


Products

Novotechnik - Vert-X 05E Series of dual angle/speed sensors

Novotechnik - Vert-X 05E Series of dual angle/speed sensors

Vert-X 05E Series of dual angle/speed sensors. The series features easy mounting in small and narrow spaces with a 5 mm body depth and mounting flanges with metal inserts. The sensors make measurements only 6 mm from edge of product for close-to-wall measurement applications. Vert-X 05E Series sensors measure angles from 0 to 360°, rotational speed and direction with repeatability to 0.1°.


Articles

Design With Touchless Rotary Sensors

Touchless rotary sensors are position sensors that use a position marker attached to an application’s rotating part plus a sensor to measure the marker’s angle.

Press Releases

Novotechnik: Compact Touchless Position Sensors

Novotechnik, U.S. introduces the TFD Series of touchless linear position sensors provide wear-free operation in tight spaces. Maximum sensor dimensions are 40 x 27 x 7 mm thin.

Novotechnik - Z-Series Magnetic Marker Types For Angle Sensor Applications

These two sensor families utilize a magnetic pickup to provide a touchless measurement range of 0 to 360° and makes measurements through air and non-magnetic materials.

Novotechnik - New Angle Sensors For Mission Critical Applications

Novotechnik, U.S. introduces the RFC4800 Series of touchless rotary angle sensors that provide absolute, rotary position. Partial and fully redundant versions are ISO-pulses and ISO 11452 tested for safety and mission critical applications.

Novotechnik U.S. introduces the Vert-X 31E Series

The sensors are touchless magnetic angle sensors with a permanent magnet that can be secured to an application's rotating shaft, so that there is no direct mechanical linkage between the shaft and the measuring system, and therefore no wear.

Novotechnik - New Touchless Angle Sensors With IO-Link

IO-Link is a standard intelligent digital interface. It's serial communication protocol makes wiring easier, needing only three wires to simultaneously transmit measured values and status information. The status bit can signal a controller if a sensor needs replacement and the controller can detect the new device and automatically configure it based on stored values minimizing down time. Parameters such as zero point can be sent and programmed into the sensor over this bus.

Novotechnik - New Customizable Angle Sensors

Novotechnik, U.S. introduces the Vert-X 2800 Series of sensors that measure angular position. These sensors convert rotational angle into an analog or digital output-depending on version.

Novotechnik - 18-bit Robust Multi-Turn Angle Sensors

Novotechnik U.S. introduces the RMB 3600 Series of absolute multi-turn angle sensors. The sensors are non-contact sensors with galvanized steel housing and stainless steel shaft with up to 100 N working shaft load for HD version. They are sealed up to IP 69K-depending on version.

Novotechnik - New Robust High Accuracy Magnetic Encoder

Novotechnik U.S. introduces the Vert-X 51 Series of rotary magnetic encoders feature up to 16-bit resolution and repeatability to 0.1° - depending on model.

Novotechnik - New Touchless In-Cylinder Sensors With 5 Output Versions

TH1 sensors have a rod that is easily mounted in-cylinder through one end and attached to the cylinder with either a threaded flange on the rod or a plug-in flange. Screw-plug hole is sized at 3/4 inch/M18 diameter and plug-in flange is 46 mm. A magnetic pick-up position marker is mounted on the application's piston rod.

Novotechnik - Basic and Programmable Touchless angle Sensors

Novotechnik U.S. introduces the Vert-X 31E Series of rotary angle sensors. The sensors are touchless magnetic angle sensors with a permanent magnet that can be secured to an application's rotating shaft, so that there is no direct mechanical linkage between the shaft and the measuring system, and therefore no wear.

Back

Search The Directory





(separate each word with a space)