RIO (Raspberry IO) Card
Roboteq, Inc launched a kickstarter project named RIO (for Raspberry IO) and aimed at creating an intelligent I/O card that stacks over the $35 Raspberry PI Linux Single Board computer.
Power for the PI from any DC source
RIO includes a 3A DC/DC converter that may be connected to a 10V to 40V DC supply, and generates the 5V needed by the PI and the RIO cards.
21 I/O lines to Connect Just About Anything
RIO provides a total of 8 digital outputs rated up to 1A and 30V max, which may also be used as digital inputs.
The card includes 13 inputs, each of which can be configured as a digital input, 0-5V analog input with 12-bit resolution, or as a timer input. In the timer mode, the inputs can capture pulse width, frequency, quadrature encoder counts, or duty cycle. Most of the input pins can also be configured as PWM outputs for driving RC servos, or dimmable lights.
Serial Connectivity and CAN Networking
Two serial ports are present on the card. One is fully RS232 compliant with programmable baud rate up to 115200 bits/s for connection to motor controllers, scanners, PC or any other RS232 device. The second is RS485 compatible, enabling, among other things, DMX512 connectivity to light show equipement. Optionally, a 3rd serial port uses TTL levels for direct interface to non-buffered, non-inverted USARTs as these found on most microcontrollers, like the Arduino.
A CAN bus interface is also present on the Rio card for connecting to CAN-compatible device, on a low cost twisted pair network at speeds up to 1Mbit/s.
Full Kickstarter details here.
DARPA's Low Cost Hand Hardware
The ARM-H track of DARPA's Autonomous Robotic Manipulation (ARM) program focuses on development of robust, low-cost and dexterous robotic hand hardware. DARPA funded performers to design and build hand mechanisms that could replace the claw-like hands currently used on robots with hands incorporating 3-4 fingers and useable palms. The teams successfully produced hands that can be manufactured for as little as $3,000 per unit (in batches of 1,000 or more), down from the $50,000 cost of current technology. The new hands also incorporate sufficient dexterity to enable manipulation of objects in their fingers when controlled by a skilled operator.
RoboBees
Demonstration of the first controlled flight of an insect-sized robot is the culmination of more than a decade's work, led by researchers at the Harvard School of Engineering and Applied Sciences (SEAS) and the Wyss Institute for Biologically Inspired Engineering at Harvard. Half the size of a paperclip, weighing less than a tenth of a gram, the robot was inspired by the biology of a fly, with submillimeter-scale anatomy and two wafer-thin wings that flap almost invisibly, 120 times per second.
Applying Motion-capture Data From Animals To Quadruped Robots
IEEE Spectrum has a short article about how the Italian Institute of Technology and the Swiss Federal Institute of Technology are using motion-capture from horses walking, trotting, etc and transferring it to the locomotion of their quadruped robots.
$45 BeagleBone Black Announced
Latest generation BeagleBone is up for sale today!
Inexpensive Tactile Sensors for Robotic Hands
TakkTile's technology leverages MEMS barometers to deliver 1-gram sensitivity for a fraction of the cost of existing systems, in a package durable enough it can survive being hit with a baseball bat. From original research paper:
A new approach to the construction of tactile array sensors based on barometric pressure sensor chips and standard printed circuit boards. The chips include tightly integrated instrumentation amplifiers, analog to digital converters, pressure and temperature sensors, and control circuitry that provides excellent signal quality over standard digital bus interfaces. The resulting array electronics can be easily encapsulated with soft polymers to provide robust and compliant grasping surfaces for specific hand designs. The use of standard commercial-off-the-shelf technologies means that only basic electrical and mechanical skills are required to build effective tactile sensors for new applications.
For $299 the TakkTile Starter Kit includes two TakkStrips cast in rubber and a Arduino Micro.
The First Level of Super Mario Bros. is Easy with Lexicographic Orderings and Time Travel.
After that it gets a little tricky.
HoverFly Cameras To Cover Upcoming Golf Events
The Golf Channel is apparently testing the use of radio controlled HoverFly cameras to cover upcoming golf events. From the captured video below i'm not sure they with be using them for actual championship play and instead just for secondary or stock shots because the copters are pretty dang loud.
National Robotics Week Meetup In New York Tomorrow
Honeybee Robotics, Huge, and the NYC Economic Development Corporation are organizing a National Robotics Week meetup in New York on April 9.
Researchers, developers and enthusiasts are gathering for an evening of presentations, live demonstrations and inspired discussion. The theme: New Frontiers in Robotics: Extending the possible. It's a chance to learn about -- and see firsthand -- how machines built and used in New York City are transcending simple automation, instead enhancing new capabilities and enabling discoveries.
What: Presentations and demonstrations of leading robotics R&D from New York City
Where: HUGE, Inc -- 45 Main St, Suite 220, Brooklyn
When: Tuesday, April 9, 7-10pm
Why: To learn, to share, to show off some cool homegrown robots
The program is listed at http://nycroboticsweek.com/. RSVP required.
Wind Turbine Inspection Robots
Helical Robotics, HR-MP20 Magnetic Platform Lifting Vehicle
Lightweight and portable design for easy deployment, use, and transport.
Mecanum wheel drive system offers best in class maneuverability.
Magnetic adhesion system does not contact the work surface.
Kirobo Tested In Zero-gravity
Kirobo, a communication robot that will be sent to the International Space Station in summer 2013 as part of a JAXA proposal is tested in a zero-gravity environment:
Festo's BionicOpter
The mechanics of dragonfly flight are unique: dragonflies can manoeuvre in all directions, glide without having to beat their wings and hover in the air. Their ability to move their two pairs of wings independently enables them to slow down and turn abruptly, to accelerate swiftly and even to fly backwards.
With the BionicOpter, Festo has applied these highly complex characteristics to an ultra-lightweight flying object at a technical level. For the first time, there is a model that can master more flight conditions than a helicopter, plane and glider combined. In addition to controlling the flapping frequency and the twisting of the individual wings, each of the four wings features an amplitude controller. This means that the direction of thrust and the intensity of thrust for all four wings can be adjusted individually, thus enabling the remote-controlled dragonfly to move in almost any orientation in space. The intelligent kinematics correct any vibrations during flight and ensure flight stability both indoors and outdoors.
Salamandra Robotica 2
Salamandra robotica II walking and swimming outdoors and performing the transition from swimming to walking indoors.
Bebionic3 Myoelectric Hand In Action
The new bebionic3 myoelectric hand, which is made from aluminium and alloy knuckles, moves like a real human limb by responding to Nigel's muscle twitches. Incredibly, the robotic arm is so sensitive it means the father-of-one can touch type on a computer keyboard, peel vegetables, and even dress himself for the first time in six years.
Low Cost Hobbyists FPGA Kickstarter
If you have been thinking of dipping your toe into the world of FPGAs (field-programmable gate arrays) but always thought they were too expensive for hobbyist then you might want to check out the 'Mojo FPGA' on Kickstarter.
The Mojo is designed to make digital design easy and cost effective for anyone who is just getting started. FPGAs do not retain their configuration when the power is lost, so they must be reconfigured every time the board is turned on. Typically, a PROM is used to load the configuration file (also known as bit file) into the FPGA automatically. The problem with that is you generally need a fairly expensive programmer to program the PROMs. The Mojo features a basic serial port (similar to an Arduino) that can be used to program a new bit file into on-board flash memory. When the board is powered on, a microcontroller reads the flash memory and configures the FPGA automatically. All that is required is a low-cost USB to serial converter.
The original Kickstarter goal was 7,000 but they blew through that goal and are currently at 70,000. If you pledge $65 dollars you get a fully assembled board.
Records 751 to 765 of 933
First | Previous | Next | Last
Industrial Robotics - Featured Product
TM Robotics - Shibaura Machine THE SCARA range
The THE range from Shibaura Machine is an extensive line up of SCARA robots. Available in four arm lengths THE400 (400mm), THE600 (600mm) and the most recent THE800 (800mm) and THE1000 (1000mm), this range is suitable for assembly, handling, inspection and pick and place processes in varied industrial applications. The THE1000 boasts a 20kg payload capacity and an impressive 0.44 second cycle time, providing high speeds for processes with large components. In fact, the range has been recognised for as the price-to-performance leader compared to other SCARA models in its price range due to its impressive speed versus payload capacity.
Robotics and Automation - Featured Company
maxon group
maxon is a leading supplier of high-precision DC brush and brushless servo motors and drives. These motors range in size from 4 - 90 mm and are available up to 500 watts. We combine electric motors, gears and DC motor controls into high-precision, intelligent drive systems that can be custom-made to fit the specific needs of customer applications.
