iCEstick $25 FPGA Evaluation Kit
Features
USB thumb drive form factor
iCE40HX-1k on board
2 x 6 position Digilent Pmod™ connector for other peripheral connections
FTDI 2232H USB device allows iCE device programming and UART interface to a PC
Vishay TFDU4101 IrDA transceiver
Five user LEDs
Discera 12 Mhz MEMS oscillator
Micron 32 Mbit N25Q32 SPI flash
USB connector provides the power supply
16 LVCMOS/LVTTL (3.3 V) digital I/O connections on 0.1” through-hole connections
Available from Lattice for $24.99
Cable Management Systems Do the Robot
Multi-axis, three-dimensional cable carriers for palletizing.
USB 3.0 Steps Up To The Plate
Upgrading existing systems or basing new designs on plug-and-play USB3 Vision-compliant video interfaces, designers can produce a winning combination of performance, ease-of-use, and cost advantages.
Paraplegic in robotic suit kicks off World Cup
From BBC:
A paraplegic man has made the first kick of the World Cup using a mind-controlled robotic exoskeleton... (cont'd)
Grantland has great story about the project here.
Response by Ray Kurzweil to the announcement of chatbot passing the Turing test
From Ray Kurzweil's blog:
In my 2004 book The Singularity Is Near, I anticipated that there would be premature announcements of this kind:
The Singularity Is Near, page 295 | Turing was carefully imprecise in setting the rules for his test, and significant literature has been devoted to the subtleties of establishing the exact procedures for determining how to assess when the Turing test has been passed. In 2002 I negotiated the rules for a Turing test wager with Mitch Kapor on the Long Now website... (cont'd)
Tessel: A Microcontroller That Runs JavaScript
From tessel.io:
Tessel is a microcontroller that runs JavaScript. It's Node-compatible and ships with Wifi built in. Use it to easily make physical devices that connect to the web.
Programmable via JavaScript
14 different hardware modules for added capabilities
Compatible with 10,000's of Node.js packages on NPM
Deploy over USB or remotely by WiFi
180mhz ARM Cortex-M3 LPC1830
32mb SDRAM
32mb Flash
TI CC3000 WiFi radio
20-pin GPIO bank for general prototyping
Micro USB or battery power
Starting at $99 (controller and one module)
Open-source 3D Printed Life-size Robot
From InMoov's homepage:
Gael Langevin is a French modelmaker and sculptor. He works for the biggest brands since more than 25 years. InMoov is his personal project, it was initiated in January 2012 InMoov is the first Open Source 3D printed life-size robot. Replicable on any home 3D printer with a 12x12x12cm area, it is conceived as a development platform for Universities, Laboratories, Hobbyist, but first of all for Makers. It’s concept, based on sharing and community, gives him the honor to be reproduced for countless projects through out the world... (cont'd)
Algorithm that harnesses data from a new sensor could make autonomous robots more nimble.
MIT paper from Andrea Censi and Davide Scaramuzza:
The agility of a robotic system is ultimately limited by the speed of its processing pipeline. The use of a Dynamic Vision Sensors (DVS), a sensor producing asynchronous events as luminance changes are perceived by its pixels, makes it possible to have a sensing pipeline of a theoretical latency of a few microseconds. However, several challenges must be overcome: a DVS does not provide the grayscale value but only changes in the luminance; and because the output is composed by a sequence of events, traditional frame-based visual odometry methods are not applicable. This paper presents the first visual odometry system based on a DVS plus a normal CMOS camera to provide the absolute brightness values. The two sources of data are automatically spatiotemporally calibrated from logs taken during normal operation. We design a visual odometry method that uses the DVS events to estimate the relative displacement since the previous CMOS frame by processing each event individually. Experiments show that the rotation can be estimated with surprising accuracy, while the translation can be estimated only very noisily, because it produces few events due to very small apparent motion... (full paper)
The Rubik and the Robot
A multi-talented control and automation team applies its mechanical, electrical, and software engineering chops to celebrate-and solve-a timeless puzzle.
National Robotics Week Was A Hit!
The fifth annual National Robotics Week was held April 5-13. Established by Congress in 2010 to raise awareness about robots and their important role in shaping the future of education, industry and the U.S. economy,
Industrial Robotics Market is Expected to Reach $41.17 Billion, Globally, by 2020
Rapid growth in automation demands, coupled with reduction of duties on refurbished goods in Asia Pacific region has fueled the growth of this market.
Leap Motion V2 Tracking
From Leap Motion's developer blog:
V2 retains the speed and positional accuracy found in V1, but the software also now tracks the actual joints and bones inside each of the user’s fingers. This leads to some immediate benefits over V1:
Finger and hand labels – every finger, hand, and joint now has anatomical labels like ‘pinky’, ‘left hand’, and ‘proximal phalanges’
Occlusion robustness – fingers are tracked even when they’re not seen by the controller, as might happen if you turned your hands completely vertically or intertwined the fingers of your left and right hands
Massively improved resistance to ambient infrared light – sunlight, powerful halogens, etc.
Much more granular data for developers about the user’s hands and fingers – 27 dimensions per hand, in addition to special parameters like grab/pinch APIs
VoCore: A Coin-sized Linux Computer With Wifi
VoCore Indiegogo Campaign:
VoCore is a coin-sized Linux computer with wifi. It is also able to work as a full functional router. It runs OpenWrt on top of Linux. It contains 32MB SDRAM, 8MB SPI Flash and using RT5350(360MHz MIPS) as its heart. It provides many interfaces such as 10/100M Ethernet, USB, UART, I2C, I2S, PCM, JTAG and over 20 GPIOs but its size is less than one square inch... ($20 USD for single unit)
Printed Hand With An Opposable Thumb
From Chiprobot on Let's Make Robots:
DARwIn-mini
Available now at Maker Shed for $499:
If you haven't checked out the amazing capabilities of the DARwIn-OP Deluxe Edition, you should! DARwIn-Mini is the younger, but no less amazing, sibling of this award winning robot. DARwIn-Mini is Dynamic Anthropomorphic Robot with Intelligence from Korea-based ROBOTIS kits, famed for their transformability and stunning humanoid designs.
Custom controller based on the 32-bit ARM Cortex M3
3D files of the robot’s parts at Thingverse
Records 1696 to 1710 of 2182
First | Previous | Next | Last
Industrial Robotics - Featured Product
DESTACO - Revolutionizing Industrial Automation
Looking for a reliable solution to enhance your automation process? Look no further than the DESTACO Robohand Grippers. These grippers are designed for the modern world of robotics, offering unparalleled performance and precision. Whether you need to grip fragile items, irregularly shaped objects, or heavy-duty components, the DESTACO Robohand Grippers have got you covered. Their modular design allows for quick and easy customization, ensuring a perfect fit for your application.
Robotics and Automation - Featured Company
PNY
PNY Professional Solutions provides customers with powerful tools to manage heavy workloads. PNY offers NVIDIA Professional, Consumer GeForce RTX, and Data Center GPU Solutions, along with PNY Memory upgrades and Solid-State Drives. All PNY products are designed and built with system integrators in mind to provide advanced application performance, top productivity, and greater power efficiency.
