What IS an Encoder?
Encoders use different types of technologies to create a signal, including: mechanical, magnetic, resistive and optical - optical being the most common.
Siemens' World-record Electric Aircraft Motor Punches Above Its Weight
From Gizmag: Researchers at Siemens have created a new prototype electric motor specifically designed for aircraft that weighs in at just 50 kg (110 lb) and is claimed to produce about 260 kW (348 hp) at just 2,500 RPM. With a quoted power five times greater than any comparable powerplant, the new motor promises enough grunt to get aircraft with take-off weights of up to 1,800 kg (2 ton) off the ground...
... As a result, the new aircraft electric drive system achieves a claimed weight-to-performance ratio of 5 kW per kilogram. This ratio is an exceptional figure – especially if compared to similarly powerful industrial electric motors used in heavy machinery that produce less than 1 kW per kilogram, or even to more efficient electric motors for vehicles that generate around 2 kW per kilogram... (full article)
Robotics, automation, and how a strong network is needed to connect it all up
Manish Sablokk for IoTTech: Cutting-edge robots and other advanced smart machines are set to be added into the rapidly expanding Internet of Things, which is projected to reach 25 billion devices by 2020. Robotics has already been used in manufacturing to great effect for over a decade, performing delicate and precise tasks with a higher success rate than humans. With advancements such as 'deep learning' robots, delivery drones and ubiquitous knowledge-sharing between machines, widespread robotics adoption is becoming far more feasible.
In healthcare, there are already robotic services in operation with automated pharmacy dispensing and robotic trolleys - robots that can navigate between floors and even call the lift using a Wi-Fi sensor. The hospitality sector has also been a keen adopter of robotics to deliver services and in education, robots are being deployed successfully as a tutor, tool or peer in learning activities, providing language, science and technology education. Cont'd...
The ABC of RPA, Part 6: Are robotics and automation in conflict with my IT Department?
It's important that your IT staff understand the impact of automation - more importantly, that it is not a replacement for your IT team.
Solving the Custom Robot Parts Challenge: The Deshazo-MFG.com Story
The number of unique parts required is high - some 200 parts in the past year or so - but the volume in which each part is needed is low, often only one or two.
Raspberry Pi And MATLAB based 3D Scanner
Raspberry Pi serves as the main controller board for the setup, capturing the images using the Pi Camera, controlling the Line LASER diode and providing control signals to the EasyDriver (Stepper Motor Driver).
University of Surrey presents a roadmap of space robotics
ABIGAIL BEALL FOR MAILONLINE: Many people spend their childhood peering up into the vast expanse of the sky, dreaming of growing up to become an astronaut. But these dreams could be dashed as the idea of people venturing into space will one day become a distant memory, according to a report published today. Robots will eventually have enough capabilities to replace humans and other animals on space missions, experts have said. Many missions involving humans in space are dangerous and expensive. But for years robots have been sent to places humans could not venture, like the rovers venturing to the edges of our solar system. According to European Space Agency (Esa) Astronaut Roberto Vittori, who launched a paper on space robotics and autonomous systems, robots can help carry out these dangerous missions. Cont'd...
Everything You Need to Know About Stepper Motors
Recent servo motors are equipped with the encoder of 20 bits (1,048,576 steps) which has a very fine resolution. Because of this, errors due to the encoder installation accuracy have a huge effect on stopping accuracy.
What's Happening in Robotics? Five Trends to Watch
2016, through mid-June, shows 56 startups received $427.5 million; and that 20 acquisitions have happened thus far totaling $4.53 bn (from the 11 reporting amounts involved).
The Third Offset Must Update Asimov's Laws of Robotics
JG Randall for The National Interest: Things tend to happen in threes. An unlikely triumvirate on the surface, it would appear that Asimov’s laws on robotics and the UN Convention on Conventional Weapons (CCW) will outflank the Third Offset—the nation’s search for its next silver bullet in war fighting is robotics—knowing that many nations will agree on moral grounds. These nations will reject Asimov based on semantics, and though the debate might be perceived as strictly academic, or even rhetorical, it is worth discussing for the sake of a good cautionary tale. Because, whether we like it or not, killer bots are coming to a theater of operation near you.
Before we get deep in the weeds, let’s get some clarity. First, let’s outline Asimov’s robotic laws. The Three Laws of Robotics are a set of rules devised by the science fiction author Isaac Asimov. They were introduced in his 1942 short story “Runaround,” although they had been foreshadowed in earlier stories. Cont'd...
Artificial muscle for soft robotics: Low voltage, high hopes
Phys.org: Soft robots do a lot of things well but they're not exactly known for their speed. The artificial muscles that move soft robots, called actuators, tend to rely on hydraulics or pneumatics, which are slow to respond and difficult to store.
Dielectric elastomers, soft materials that have good insulating properties, could offer an alternative to pneumatic actuators but they currently require complex and inefficient circuitry to deliver high voltage as well as rigid components to maintain their form—both of which defeat the purpose of a soft robot.
Now, researchers at the Harvard John A. Paulson School of Engineering and Applied Sciences (SEAS) have developed a dielectric elastomer with a broad range of motion that requires relatively low voltage and no rigid components. They published their work recently in Advanced Materials. Cont'd...
Robot Vision vs Computer Vision: What's the Difference?
Unlike pure Computer Vision research, Robot Vision must incorporate aspects of robotics into its techniques and algorithms, such as kinematics, reference frame calibration and the robot's ability to physically affect the environment.
The ABC of RPA, Part 5: What Is the Cost of Automation and How Do I Justify It to the Leadership Team?
We've put together a breakdown of the cost of automation, and how to justify it to the leadership team.
Ford's new robots can build cars, make coffee
Ford Motor Company announced today its early testing of a new type of assembly line robot that were co-developed with German robotics company KUKA Roboter GmbH with the intention of assisting human line workers. Two of these three-foot-tall machines are in use at the Cologne, Germany factory, where they assist human workers to install shock absorbers on Ford Fiestas. These workers would have originally had to juggle the shocks and tools to install them, but now the robot helps them position and install the parts. More...
How Using the Latest 3D Simulation Software for Vision Guided Robotic Applications Will Save You Time and Money
It is easy to imagine the time saved by using the latest simulation tools to develop vision guided robotic applications.
Records 811 to 825 of 1955
First | Previous | Next | Last
Featured Product
BLE2 Series Brushless Motor & Driver
The BLE2 Series replaces our popular BLE Series and continues our brushless motor advantages by featuring an all new compact, high-power and high-efficiency brushless DC motor combined with a Driver that can be digitally set and controlled via external DC voltage or by the front panel.
The BLE2 Series can easily compete with larger 3-phase inverter driven motors in many more applications, with built-in simple holding torque function, saving space and increasing performance thanks to the advantages of a brushless motor design. The BLE2 Series has a maximum speed of 4000 r/min, achieving a speed ratio of 1:50 (80 to 4000 r/min). The new motor structure is small than previous models and enables high power and high efficiency while incorporating easy setting, installation and wiring. The new motor connector offers IP66 degree of protection and allows for easy and direct connection between motor and driver with two available orientation of cable outlet direction. Standardized use of stain
