Republican-Leaning Cities Are At Greater Risk Of Job Automation

By Jed Kolko for Five Thirty Eight:  More and more work activities and even entire jobs are at risk of beingautomated by algorithms, computers and robots, raising concerns that more and more humans will be put out of work. The fear of automation is widespread — President Obama cited it as the No. 1 reason Americans feel anxious about the economy in his State of the Union address last month — but its effects are not equally distributed, creating challenges for workers and policymakers. An analysis of where jobs are most likely to face automation shows that areas that voted Republican in the last presidential election are more at risk, suggesting that automation could become a partisan issue. So-called “routine” jobs — those that “can be accomplished by following explicit rules” — are most at risk of automation. These include both “manual” routine occupations, such as metalworkers and truck drivers, and “cognitive” routine occupations, such as cashiers and customer service reps.1 Whereas many routine jobs tend to be middle-wage, non-routine jobs include both higher-wage managerial and professional occupations and lower-wage service jobs.   Cont'd...

Humanoid robots in tomorrow's aircraft manufacturing

From Phys.Org:  Developing humanoid robotic technology to perform difficult tasks in aircraft manufacturing facilities is the goal of a four-year joint research project, which is being conducted by the Joint Robotics Laboratory (CNRS/AIST) and Airbus Group. It will officially be launched on 12 February 2016 at the French Embassy in Tokyo. The introduction of humanoids on aircraft assembly lines will make it possible to relieve human operators of the most laborious and dangerous tasks, thus allowing them to concentrate on higher value-added ones. The primary difficulty for these robots will be to work in a confined environment and move without colliding with the numerous surrounding objects. This is the first issue researchers will have to solve by developing new algorithms for the planning and control of precise movements.   Cont'd...  

Smart Factories Need Smart Machines

Industry 4.0 Smart Factories and Smart Machines continue to drive dramatic efficiency improvements across the supply chain, within the factory and inside machines.

Five Business Tips for Robot Integrators

Manufacturing partners need you just as much as you need them. Stay loyal because they can really help you in the early days.

Distributed Control Systems Simplify the Three C's of Robotics

Borrowed from the military, Communications, Command and Control (sometimes called 3C), are the three key organizing principles for acquiring, processing and disseminating information

Robotics in the Folding Carton Industry: The Human Factor

As they watch fellow companies successfully use robotics, see what it takes to switch to a fully or semi-automated system and be reassured by a human back-up system, it seems inevitable that more folding carton manufacturers will soon be adopting robotics.

Global Expert Platform for Production Services in Additive Manufacturing

The services that fabb.one will provide through their fabbs range from printing, injection molding, CNC milling to scanning, conceptual and CAD design.

Factory Automation Will Speed Forward with A.I., Says Bernstein

By Tiernan Ray for Barron's:  Bernstein Research’s Alberto Moel, who follows tech-industrial companies such as Corning(GLW) and AU Optronics (AUO), this afternoon offered up a thinks piece on robotics andfactory automation, arguing that some of the costs of automation beyond the basic cost of the robot are about to get dramatically cheaper, thanks in large part to artificial intelligence akin to what Alphabet (GOOGL) and others are doing. Moel notes that the basic components of factory robots are only falling by perhaps 6% per year, their cost reduction bounded by things such as casings and servomotors and reduction gears that don’t rapidly fall in cost. But, writes Moel, the cost to install and adjust these machines on a factory floor is ten times their component cost and that stuff can be reduced more dramatically: How much this integration costs varies widely. An often-cited rule of thumb is that a $50,000 robot will need $500,000 of integration costs before it is all said and done. Of course, these integration costs can be amortized over many robots, so perhaps a better estimate would be 3-5x the robot cost [...] But I do believe we are at an inflection pointthat will materially increase the capability of automation systems and substantially reduce programming, setup, and fixturing costs which are the largest cost element in most automation efforts. So instead of a measly 6% YoY cost reduction , we get 25-30% YoY declines, and automation Nirvana.   Cont'd.. .

Most Popular Articles for 2015 - Did some of them predict the future?

Smart Homes, Robotics, Automation, Unmanned Vehicles, Solar and Wind Energy. Regardless of where you work or what you do, these topics are affecting your life and will continue to do so in the future.

Special Tradeshow Coverage for Advanced Manufacturing Conference & Expo 2016

Advanced Manufacturing Conference & Expo 2016 will be held from February 9th - 11th in Anaheim, California. This RoboticsTomorrow.com Special Tradeshow report aims to bring you news, articles and products from this years event.

Robotics 2016: Doubling Throughput in Distribution and Factory Operations

Two existing bakery facilities were successfully integrated into one and finished goods capacity nearly doubled from 6,500 lbs. /hour to 12,000 lbs. /hour.

Time-of-Flight Camera - An Introduction

In this paper, we introduce the TOF technology and the theory of operation. We also compare TOF sensors with 2D machine vision and other 3D vision technologies and highlight TOF sensors differentiating advantages.

Building the Steam Controller

From Valve: When we first started designing hardware at Valve, we decided we wanted to try and do the manufacturing as well. To achieve our goal of a flexible controller, we felt it was important to have a similar amount of flexibility in our manufacturing process, and that meant looking into automated assembly lines. It turns out that most consumer hardware of this kind still has humans involved in stages throughout manufacturing, but we kind of went overboard, and built one of the largest fully automated assembly lines in the US. Our film crew recently put together a video of that assembly line, showcasing exactly why robots are awesome.

Getting Started with Collaborative Robots? Part 1 - What can collaborative robots do?

This is the first in a series of articles about Collaborative Robots

Father of Robotics Joseph F. Engelberger Dies at Age 90

Joseph F. Engelberger, an engineer and entrepreneur who pioneered the robotics field, died peacefully at his home this morning, December 1, 2015, in Newtown, Connecticut. Engelberger - widely known as the "Father of Robotics" and creator of the world's first industrial robot - revolutionized modern industrial and automotive manufacturing processes and went on to establish robotics in human services. Engelberger was 90 years old.  Engelberger, an industry advocate, author, and international ambassador for robotics, founded Unimation, Inc., in 1956, the world's first industrial robotics manufacturer. Working closely with inventor George Devol, he developed the first industrial robot in the U.S., called "Unimate", which was installed for industrial use in a General Motors plant in 1961. Since then, approximately three million industrial robots have been installed in manufacturing facilities around the world.   Full Press Release.

Records 481 to 495 of 640

First | Previous | Next | Last

Factory Automation - Featured Product

 Goudsmit Magnetics – Magnetic robot grippers for automated processes

Goudsmit Magnetics - Magnetic robot grippers for automated processes

Magnetic robot end-of-arm tooling are suitable for the automated pick-up and positioning of steel or other ferromagnetic objects. They can be switched on and off and have a threaded mounting hole for robots. Magnetic grippers are an efficient alternative for traditional robot grippers. Application in automated production lines and for robots and pick-and-place systems. Magnetic product handling reduces the duration and number of operations. Goudsmit Magnetics is driven by magnetism since 1959. See how it works: https://youtu.be/hcXJ98mXHZE